When not engaged the diaphragm is closed and no water should flow.

Replacing a Primary Water Inlet Valve in Your Refrigerator. Find the water supply line coming into the valve and turn it off at the source (typically under the sink). Safely store any food that could deteriorate while the power is off. Remove the back panel and trace the water tube from the water dispenser to the valve to discover the solenoid inlet valve responsible for switching on the water flow. Thanks in advance. A solenoid is simply an electromagnet. To check on the water inlet valve, unplug the refrigerator and shut off the water supply to it. Most foods will be okay if left in the refrigerator as long as the doors are closed; power will be off for only about 30 minutes when checking the valve. changes bin eye boards. Water lines in the fridge were not freezing. A replacement water inlet valve for your LG LSC27935SB refrigerator. If this valve is damaged, cracked, or the water line is not fully connected, it will leak. Remove the screws that secure the inlet valve in place. A few months back my refrigerator iced up so I defrosted it and ever since my ice maker hasn't made ice the fill line from the water inlet valve to the ice maker has water in it but no ice what are some areas that I can check to pinpoint the problem Thanks. I have GE fridge model GSS25KGSACC. To check the water valve, unplug the refrigerator and shut off the water supply to the refrigerator. Brad for Model Number FFHS2611PFCA. Wear work gloves to protect your hands. Problem appears to be that the solenoid on the water inlet valve is not getting power to or from the door switch. Answer Brad, Cycle the icemaker and test to see if there is 120 vac getting to the valve. Don't have wiring diagram. Free shipping . If you are now getting 100 volts and no water fill the water valve is defective. (#20 Above Image) If 1/4" saddle type valve (Click for Photo) supplies water to inlet valve #20 Above Check saddle valve … If the water pressure is sufficient, use a multimeter to check for power to the water inlet valve. Picture Information.

If you are still getting only 15 volts unplug the refrigerator again. Opens … Make sure that the water pressure to the valve is at least 20 psi. If it's not frozen, you'll need to replace the electronic water valve on the back of the refrigerator where your water supply line from your house connects to your refrigerator itself. T he water inlet valve is located behind your refrigerator. Whirlpool side by side, ice maker not producing, no power to water inlet valve. As soon as the water valve's solenoid coil is powered, the armature allows the diaphragm to flex opening the passage and allowing water to flow. As this repair deals with an area that can manifest in some water leakage, it is crucial that you make sure there is no power running to your refrigerator beforehand. WR57X10033 Refrigerator Water Valve Fit for GE Hotpoint Kenmore by Beaquicy. I am stumped where to go next. If the water pressure is sufficient, use a multimeter to check for power to the water inlet valve. bypassed the whole filter with direct line to inlet valve works for ice still no door water. At the end of the ice maker cycle watch your meter to see what the voltage is. Fill Tube Frozen Up. Caution: Please read our safety information before attempting any testing or repairs. In a water fill valve, the solenoid's actuator is attached to a diaphragm which opens or closes a route through which water can pass. Sean for Model Number GB2FHDXWS02.

No Water In I/M Mold Fill Tube Frozen Up.

I ordered a water inlet valve but that did not fix the problem. $18.25. The water inlet valve where the water line connects into at the back of the refrigerator may also have a slight leak that causes a puddle of water. The dispenser micro switch is a momentary contact switch that when actuated will supply power to the solenoid on the water inlet valve. I justed replaced the water inlet valve kit (Part Number AP3160649) on my KitchenAid Side by Side refrigerator. Disconnect the supply line. If the water inlet valve has sufficient pressure and is getting power, but the ice maker won’t fill with water to make ice, replace the water inlet valve. Free shipping . Make sure that the water pressure to the valve is at least 20 psi. The water from the new water inlet repair kit will not push water up through the hose to the water dispenser on the front of the refrigerator. Solution: Unplug fridge from power and slide it out from the wall. Saddle tap valve wasn’t a problem. This Refrigerator Water Inlet Valve supplies water to the ice maker and water dispenser in your refrigerator. 3 thoughts on “ No Water from the Dispenser on a GE Refrigerator ” Bowtie August 6, 2010 at 11:43 pm. How to test a refrigerator micro switch with a multi-meter: Disconnect the refrigerator from the power source and turn off the water supply before beginning.